View MIC2529_31520.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MIC2529
Micrel
MIC2529
Single-Channel USB Power Controller Advance Information
General Description
The MIC2529 is a high-side power switch optimized for selfpowered (individual port switching) and bus-powered (ganged port switching) Universal Serial Bus (USB) hub applications. An on-board voltage regulator provides the 3.3V supply voltage needed for many USB microcontrollers reducing board component count. The MIC2529 satisfies the following USB requirements: it supplies up to 500mA as required by USB downstream devices; the switch's low on-resistance meets USB voltage drop requirements; fault current is limited to typically 750mA, well below the UL 25VA safety requirement; and a flag output is available to indicate fault conditions to the local USB controller. Soft start eliminates the momentary voltage drop on the upstream port that may occur when the switch is enabled in bus-powered applications. A low-dropout (LDO) regulator provides 3.3V at loads up to 100mA and includes an enable pin for low current shutdown. Both enable inputs are compatible with 3.3V and 5V logic. Thermal shutdown prevents catastrophic failure from highcurrent loads. The MIC2529 is available in an 8-pin SOIC package with active-high or active-low enable circuitry on switch.
Features
* * * * * * * * * * * * * Compliant to USB specifications UL Recognized Component On-board 3.3V, 100mA low-dropout regulator 500mA minimum continuous switch load current 160m maximum on-resistance 750mA typical current limit Open-drain fault flag pin for switch Output can be forced higher than input (off-state) Thermal shutdown 1ms turn-on (soft-start) and fast turnoff Available with active-high or active-low switch enable Active-high enable on 3.3V regulated output 8-pin SOIC package
Applications
* USB self-powered hubs * USB bus-powered hubs * USB keyboard hubs
Typical Applications
Upstream VBUS D+ D- GND 3.3V USB Controller V+ ON/OFF
8
4.40V to 5.25V 4.7 F 0.1 F MIC2529 10k 0.1F 10k EN FLG 3VEN GND IN OUT OUT 3VOUT
3 2 7 4 1 6 5
Ferrite Bead VBUS 33F 0.01F D+ D- GND Downstream USB Port 1 100mA max.
OVERCURRENT D- D+ 1.5k* 5% 1F GND
VBUS 33F 0.01F D+ D- GND Downstream USB Port 2 100mA max.
Bold lines indicate 0.1" wide, 1-oz. copper high-current traces.
VBUS 33F 0.01F D+ D- GND Downstream USB Port 3 100mA max.
* Speed sense termination resistor. Must be connected between V3VOUT and D+ to indicate high speed operation.
VBUS 33F 0.01F D+ D- GND Downstream USB Port 4 100mA max.
33F tantalum or 100F electrolytics are recommended.
4-Port Ganged Bus-Powered Hub
UL Recognized Component
June 1999
1
MIC2529
MIC2529
Micrel
Ordering Information
Part Number MIC2529-1BM MIC2529-2BM Switch Enable Active High Active Low Temperature Range -40C to +85C -40C to +85C Package 8-Pin SOIC 8-Pin SOIC
Pin Configuration
MIC2529
FLG 1 OUT 2 IN 3 3VOUT 4 8 EN 7 OUT 6 3VEN 5 GND
8-Pin SOIC (M)
Pin Description
Pin Number 1 2, 7 3 4 5 6 8 Pin Name FLG OUT IN 3VOUT GND 3VEN EN Pin Function Fault Flag (Output): Active-low, open-drain output. Indicates overcurrent and thermal shutdown switch conditions. Switch Output: Output MOSFET source. Typically connected to switched side of load. Pin 2 and 7 must be connected together externally. Supply Voltage Input. Supply to switch and regulator. Connect to positive supply. 3.3V Regulator Output Ground: Supply return. Regulator Enable (Input): Logic-compatible input. Logic high = enable, logic low or open = shutdown. Do not float. Switch Enable (Input): Logic-compatible enable input. High input = 2.1V typical. Low input = 1.9V typical. (-1 active high, -2 active low) Do not float.
MIC2529
2
June 1999
MIC2529
Micrel
Absolute Maximum Ratings (Note 1)
Supply Voltage (VIN) ..................................................... +6V Fault Flag Voltage (VFLG) .............................................. +6V Fault Flag Current (IFLG) ............................................ 50mA Switch Output Voltage (OUT) ........................................ +6V Switch Output Current (IOUT) ................... Internally Limited Switch Control Input (VEN) ........................... -0.3V to +12V Regulator Control Input (V3VEN) .................... -20V to +20V Storage Temperature (TS) ....................... -65C to +150C Lead Temperature (soldering 5 sec.) ........................ 260C
Operating Ratings (Note 2)
Supply Voltage (VIN) ...................................... +3V to +5.5V Ambient Temperature (TA) ......................... -40C to +85C Thermal Resistance SOIC (JA) ......................................................... 160C/W
Electrical Characteristics
VIN = +5V; TA = 25C; unless noted. Parameter Supply Current Condition V3VEN = high, switch EN off, Note 3 V3VEN = high, switch EN on, OUT = open, Note 3 EN Input Threshold Enable Input Current Enable Input Capacitance Switch Resistance VIN = 5V; IOUT = 500mA VIN = 3.3V; IOUT = 500mA Output Turn-On Delay Output Turn-On Rise Time Output Turnoff Delay Output Turnoff Fall Time Output Leakage Current Continuous Load Current Short Circuit Current Limit Current-Limit Threshold Overtemperature Shutdown Threshold Error Flag Output Resistance FLG not active enabled into load, VOUT = 0V ramped load applied to enabled output, VOUT = 0V, Note 4 TJ increasing TJ decreasing VIN = 5V, IL = 10mA VIN = 3.3V, IL = 10mA Error-Flag Off Current 3VEN Input Threshold VFLAG = 5V enable input logic-low voltage (regulator shutdown) enable input logic-high voltage (regulator enabled) 3VEN Input Current VIL 0.4V VIH 2.0V 2.0 0.01 5 -1 20 0.5 0.5 0.75 0.95 135 125 20 30 0.01 1 0.4 1.25 1.50 RL = 10 RL = 10 RL = 10 RL = 10 low to high transition high to low transition, Note 3 VEN = 0 - 5.5V Min Typ 80 160 2.1 1.9 0.01 1 120 160 0.25 3 1 1 20 20 10 Max 150 300 2.4 Units A A V V A pF m m ms ms s s A A A A C C A V V A A
0.8
June 1999
3
MIC2529
MIC2529
Parameter Regulator Output Voltage Regulator Output Voltage Temperature Coefficient Regulator Line Regulation Regulator Load Regulation Regulator Dropout Voltage Regulator Current Limit
Note 1. Note 2. Note 3. Note 4. Note 5. Note 6.
Micrel
Condition VIN = 4.0V to 5.25V, IL = 100mA Note 5 VIN = 4.0V to 5.25V IL = 0.1mA to 100mA IL = 100mA, Note 6 3VOUT = 0V 320 Min 3.14 Typ 3.3 50 0.3 3 Max 3.47 Units V ppm/C mV mV mV mA
Exceeding the absolute maximum rating may damage the device. Devices are ESD sensitive. Handling precautions recommended. The device is not guaranteed to function outside its operating rating. Off is 0.8V and on is 2.4V for the MIC2529-1 switch. Off is 2.4V and on is 0.8V for the MIC2529-2 switch. The enable input has approximately 200mV of hysteresis. See control threshold charts. Limits do not include 3VOUT load current of 100A during test. See "Functional Characteristics: Current-Limit Response" photo. Output voltage temperature coefficient is defined as the worst case voltage change divided by the total temperature range. Dropout voltage is defined as the input to output differential at which the output voltage drops 2% below its nominal value measured at 1V differential.
Typical Characteristics
Output On-Resistance vs. Supply Voltage
ON-RESISTANCE (m)
140 OUTPUT RESISTANCE (m)
140
Output On-Resistance vs. Temperature
SUPPLY CURRENT (A)
On-State Supply Current vs. Supply Voltage
200 160 120 80 40 TA = 25C 0 2 3 4 5 SUPPLY VOLTAGE (V) 6
120
120
Awaiting Further Characterization Data
100 RL = 44 T = 25C 80 3.0 3.5 4.0 4.5 5.0 SUPPLY VOLTAGE (V) 5.5
100
Awaiting Further Characterization Data
80
RL = 44 VIN = 5V
60 -40 -20 0 20 40 60 80 100 TEMPERATURE (C)
On-State Supply Current vs. Temperature
200 SUPPLY CURRENT (A)
SUPPLY CURRENT (A) 2.0
Off-State Supply Current vs. Supply Voltage
SUPPLY CURRENT (A)
2.0
Off-State Supply Current vs. Temperature
180 160 140 120 100 80 60 40 VIN = 5V 20 0 -40 -20 0 20 40 60 80 100 TEMPERATURE (C)
1.5
1.5
Awaiting Further Characterization Data
1.0
Awaiting Further Characterization Data
1.0
Awaiting Further Characterization Data
0.5 TA = 25C 0 2 3 4 5 SUPPLY VOLTAGE (V) 6
0.5 VIN = 5V 0 -40 -20 0 20 40 60 80 100 TEMPERATURE (C)
MIC2529
4
June 1999
MIC2529
Micrel
SWITCH ENABLE VOLTAGE (V)
SWITCH ENABLE VOLTAGE (V)
2.5
Switch Enable Threshold vs. Supply Voltage
2.5
Switch Enable Threshold vs. Temperature
5 4 TIME (ms) 3 2 1
Output Rise Time vs. Temperature
VEN RISING 2.0 VEN FALLING 1.5
2.0 VEN FALLING 1.5
VEN RISING
Awaiting Further Characterization Data
1.0 3.0
TA = 25C 3.5 4.0 4.5 5.0 SUPPLY VOLTAGE (V) 5.5
1.0 -40 -20 0 20 40 60 80 100 TEMPERATURE (C)
VIN = 5V
VIN = 5V 0 -40 -20 0 20 40 60 80 100 TEMPERATURE (C)
50 40 TIME (s) 30 20 10
Output Fall Time vs. Temperature
SWITCH OUTPUT (A)
3
Threshold Trip Current vs. Supply Voltage
SWITCH OUTPUT (A)
3
Short Circuit Output Current vs. Temperature
2
Awaiting Further Characterization Data
Awaiting Further Characterization Data
1
2
Awaiting Further Characterization Data
1
VIN = 5V 0 -40 -20 0 20 40 60 80 100 TEMPERATURE (C) 0 0
TA = 25C 1 2 3 4 SUPPLY VOLTAGE (V) 5
VIN = 5V 0 -40 -20 0 20 40 60 80 100 TEMPERATURE (C)
3.0 THRESHOLD VOLTAGE (V)
UVLO Threshold Voltage vs. Temperature
DROPOUT VOLTAGE (V)
1000
Regulator Dropout Voltage vs. Output Current
400 DROPOUT VOLTAGE (V) 350 300 250 200 150 100 50
Regulator Dropout Voltage vs. Temperature
2.5
RISING
100
FALLING 2.0
Awaiting Further Characterization Data
10
Awaiting Further Characterization Data
1.5 -40 -20 0 20 40 60 80 100 TEMPERATURE (C)
1 0.01
0.1 1 10 100 OUTPUT CURRENT (mA)
0 -40 -20 0 20 40 60 80 100 TEMPERATURE (C)
June 1999
5
MIC2529
MIC2529
Micrel
Functional Characteristics
Short-Circuit Response Short Applied to Output Short Circuit Transient Response Short Applied to Output
VFLG (5V/div.)
VOUT (2V/div.)
Thermal Shutdown
IOUT (500mA/div.)
VIN = 5V RL = 0.3 TIME (100ms/div.)
IOUT (0.5A/div.)
VOUT (2V/div.)
VFLG (5V/div.)
VIN = 5V
TIME (100s/div.)
Short Circuit Response Enabled into Short Circuit
VFLG VEN (5V/div.) (5V/div.)
Current Limit Response
VOUT (2V/div.)
VOUT (2V/div.)
VFLG (5V/div.)
Thermal Shutdown
1.24A Current Limit Threshold
IOUT (500mA/div.)
(Regulator Disabled) VIN = 5V
IOUT (500mA/div.)
VIN = 5V
TIME (100ms/div.)
TIME (5ms/div.)
Turn-On and Turnoff Characteristics
VFLG VEN (5V/div.) (5V/div.)
off on off
Turn-On and Turnoff Characteristics
VFLG VEN (5V/div.) (5V/div.)
off on off
100s
IOUT (100mA/div.)
VOUT (2V/div.)
VIN = 5V RL =40 CL = 10F TIME (1ms/div.)
IOUT (500mA/div.)
VOUT (2V/div.)
VIN = 5V RL = 40 CL = 150F TIME (5ms/div.)
MIC2529
6
June 1999
MIC2529
Micrel
Test Circuit
IIN 5V 0.1F VEN VFLG V3VEN 10k MIC2529 IN OUT OUT 3VOUT CL 0.1F RL VOUT IOUT Ferrite Bead
EN FLG 3VEN GND
Functional Characteristics Test Circuit
Block Diagram
3.3V LDO REG
3VEN EN OSC. THERMAL SHUTDOWN 1.2V REFERENCE
3VOUT
IN
CHARGE PUMP GATE CONTROL
CURRENT LIMIT
OUT
FLG MIC2529-x GND
June 1999
7
MIC2529
MIC2529
Micrel
Switch Current Sensing and Limiting The current limit threshold is preset internally. The preset level prevents damage to the switch output MOSFET and external load but allows a minimum current of 0.5A through the switch output MOSFET. The current limit circuit senses a portion of the output switch (FET) current. The current sense resistor shown in the block diagram is virtual and has no voltage drop. The reaction to an overcurrent varies with three scenarios:
Functional Description
The MIC2529-1 and MIC2529-2 are high-side power switches with on-board voltage regulators. Switch fault conditions turn off or inhibit turn-on of the output transistor, depending upon the type of fault, and activate the open-drain error flag transistor, making it sink current to ground. Input and Output IN (input) is the power supply connection to the logic circuitry, drain of the output MOSFET, and the voltage regulator input. 3VOUT is the regulated 3.3V output. OUT (output) is the source of the MOSFET switch. In a typical circuit current flows through the switch from IN to OUT toward the load. Both OUT pins must be connected together externally. If VOUT is greater than VIN when a switch is disabled, current will flow from OUT to IN when the switch is enabled since the switch is bidirectional when enabled. The output MOSFET and driver circuitry are also designed to allow the MOSFET source to be externally forced to a higher voltage than the drain (VOUT > VIN) when the output is off. Thermal Shutdown Thermal shutdown shuts off the switch and activates the flag if the die temperature exceeds 135C. 10C of hysteresis prevents the switch from turning on until the die temperature drops to 125C. Switch overtemperature detection functions only when the switch is enabled. The internal LDO regulator has a similar shutdown without flag output. When an excessive load is applied to the switch output, the MIC2529 will enter a thermal shutdown condition. As shown in the "Electrical Characteristics" short-circuit response graphs, the thermal time constant is about 640ms for the initial condition. If the channel is not shut off, the output will go into thermal oscillation with a frequency of about 20Hz. While this will not damage the device, it is recommended that the port is shut down prior to this occurring.
Switch Enabled into Short Circuit If the switch is powered on or enabled into an excessive load or short circuit, the switch current ramps up to a constant current. The fault flag goes low until the load is reduced. See the "Functional Characteristic: Short Circuit Response, Enabled into Short Circuit" photo. Short Circuit Applied to Outputs When a heavy load or short circuit is applied to an enabled switch, a large transient current will flow until the current limit circuitry responds. Once this occurs, the device limits current to less than the short circuit current specification. See "Functional Characteristic: Short Circuit Response, Short Applied to Output" graph. Current-Limit Response The MIC2529 current-limit profile exhibits a small foldback effect of approximately 200mA. Once this current-limit threshold is exceeded the device enters constant-current mode. This constant current is specified as the short circuit current limit in the "Electrical Characteristics" table. It is important to note that the MIC2529 will deliver load current up to the current-limit threshold. Refer to "Functional Characteristics: Current-Limit Response" photo for details. Fault Flag FLG is an open-drain N-channel MOSFET output. The fault flag is active (low) for one or more of the following switch conditions: current limit or thermal shutdown. The flag output MOSFET is capable of sinking a 10mA load to typically 100mV above ground. The flag does not indicate faults in the LDO regulator.
MIC2529
8
June 1999
MIC2529
Micrel
"Functional Characteristics: Switch Turn-On and Turnoff Characteristics" for details. During the charging time, the device enters into constant-current mode and the flag is activated. As the capacitance is charged, the current decreases below the short circuit current-limit threshold and the flag will be deasserted.
V+
Applications Information
Supply Filtering A 0.1F to 1F bypass capacitor from IN to GND, located at the device, is strongly recommended to control supply transients. See Figure 1. Without a bypass capacitor, an output short may cause sufficient ringing on the input (from supply lead inductance) to damage internal control circuitry. Input or output transients must not exceed the absolute maximum supply voltage (VIN(max) = 6V) even for a short duration.
4.0V to 5.5V
1 2 3
USB Controller OVERCURRENT ON/OFF
10k 10k 0.1F
MIC2529
1 2 3 4
FLG OUT IN 3VOUT
EN OUT 3VEN GND
8 7 6 5
MIC2529 FLG OUT IN 3VOUT EN OUT 3VEN GND
8 7 6 5
0.1F to 1F
4
1F
Figure 2. Transient Filter In USB applications it is required that output bulk capacitance, shown in "Typical Application," is utilized to meet transient regulation requirements during hot-plug events. When the MIC2529 is enabled into this capacitive load, the flag may go active for about 200s. Additionally, during hotplug events, inrush currents will also cause the flag to go active for approximately 30s. Since these conditions are not valid overcurrent faults, the USB controller must ignore the flag during these events. To prevent this erroneous overcurrent reporting, a 1ms RC filter must be used (see Figure 2). Bus-Powered Hub Applications The MIC2529 was designed for self-powered or bus-powered hubs. The integrated regulator reduces cost and space in applications using a 3.3V USB controller. For self-powered hubs, the MIC2529 will support 1 downstream port. For buspowered hubs, the MIC2529 will support up to four ganged downstream ports. Bus-Powered Hub Port Switching The USB Specification requires that bus-powered hubs implement port switching on either a ganged or individual basis. The specific implementation must be reported via the Hub Descriptor Status Register. Individual port switching does have some advantages in that a fault on one port will not prevent the other ports from operating correctly. In addition, a soft-start circuit must be included in order to reduce inrush currents when the switch is enabled. To meet this requirement, the MIC2529 has been designed to slowly ramp its output. The USB Specification does not require bus-powered hubs to report overcurrent conditions to the host since the hub is already current-limited at the upstream port. However, if it is desired to report overcurrent, the Hub Descriptor Status Register must be programmed to indicate this. The MIC2529 provides a flag output for this application.
Figure 1. Supply Bypassing Regulator Output Capacitor A 1F output capacitor is required between 3VOUT and GND to prevent oscillation. Larger values improve the regulator's transient response. The output capacitor value may be increased without limit. The output capacitor should have an ESR (effective series resistance) of about 5 or less and a resonant frequency above 1MHz. Most tantalum or aluminum electrolytic capacitors are adequate. Film types will work but are more expensive. Since many aluminum electrolytics have electrolytes that freeze at about -30C, solid tantalums are recommended for operation below -25C. The regulator will remain stable and in regulation with no load other than the internal voltage divider, unlike many other voltage regulators. Switch Enable Input EN must be driven logic high or logic low for a clearly defined input. Floating the input may cause unpredictable operation. EN should not be allowed to go negative with respect to GND. Regulator Enable Input Forcing 3VEN (regulator enable/shutdown) high enables the regulator. Like EN, 3VEN is compatible with CMOS logic gates. If the enable/shutdown feature is not required, connect 3VEN to IN. Transient Overcurrent Fault-Flag Filter When the MIC2529 is enabled, large values of capacitance at the output of the device may cause inrush currents to flow that exceed the short circuit current-limit threshold of the device and cause the flag to activate. The duration of this time depends on the size of the output capacitance. Refer to
June 1999
9
MIC2529
MIC2529
Suspend Current Universal Serial Bus Specification places a maximum suspend current requirement of 500A on devices. For hubs, Universal Serial Bus Specification Revision 1.1 clarifies this issue. Revision 1.1, section 7.2.3, stipulates that the maximum suspend current for a configured hub is 2.5mA. This number is derived by allocating 500A for up to four downstream ports plus 500A for the hub's internal functions. A nonconfigured hub is considered a low-power device and cannot consume more than 500A. In a nonconfigured state all downstream devices will be switched off. In most cases, a nonconfigured hub is not a practical state for the system. Therefore, the 2.5mA specification is the applicable target specification for the suspend state. In a bus-powered hub with less than 4 ports, the hub may use the additional current for internal functions.
Micrel
The 500A worst-case suspend current must be further divided among the data port termination resistors and internal functions. The termination resistors will consume 3.6V / (16.5k - 5%) = 230A worst case. This leaves only 270A for internal functions. Assuming 100A as the maximum USB controller suspend current, 170A remains for the rest of the system. The MIC2529 will consume 150A maximum, leaving a margin of 20A. USB Voltage Regulation USB specifications require a minimum downstream voltage supply of 4.40V from a bus-powered hub port (see Application Note 17 for details). The USB specification allows for a 100mV drop across the hub, leaving 250mV for PCB, upstream cable, and connector resistance. Therefore, the onresistance of the switch for each port, not including PCB resistance, must be about 100mV / 100mA = 1. For a 4-port ganged hub, this resistance reduces to 250m. The MIC2529 easily satisfies this requirement.
MIC2529
10
June 1999
MIC2529
Micrel
Package Information
0.026 (0.65) MAX)
PIN 1
0.157 (3.99) 0.150 (3.81)
DIMENSIONS: INCHES (MM)
0.050 (1.27) TYP
0.020 (0.51) 0.013 (0.33) 0.0098 (0.249) 0.0040 (0.102) 0-8 SEATING PLANE 45 0.010 (0.25) 0.007 (0.18)
0.064 (1.63) 0.045 (1.14)
0.197 (5.0) 0.189 (4.8)
0.050 (1.27) 0.016 (0.40) 0.244 (6.20) 0.228 (5.79)
8-Pin SOIC (M)
June 1999
11
MIC2529

▲Up To Search▲

Price & Availability of MIC2529

	To Download MIC2529 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .